Installation Information Frequently asked questions (Q) Which Pantera Electronic product should I install first? (A) The ATO Fuse Panel is the distribution of electrical power through out the car. The factory Fuse panel has many design deficiencies and cannot be safely repaired. Replace the fuse panel first. (Q) Is the temperature sensor for the RFC the same as the temperature switches in the Fluidyne radiator? (A) No, the temperature sensor included with the RFC is not a temperature sensing switch. You will need to purchase the Fluidyne radiator adapter for the sensor. (Q) Will I need 2 temperature sensors for the RFC to replace both temperature switches in the Fluidyne radiator? (A) No. only the top sensor port is used on the Fluidyne radiator, the other temperature switch can be left in as a plug. (Q) Are Pantera Electronics products compatible with Bob Timma fuse panel and Rick Mosely relay kits? (A) No, it is not recommend to install PE products with “after-market kits”. “After-market kits” will require removal before installing PE products. Many of our customers find it worthwhile to remove the dated fixes to up-grade to modern technology. (Q) Are all Pantera Electronic products compatible with each other? (A) Yes, all Pantera Electroncis products are compatible with each other ... some PE installation manuals specify connections if multiple products are installed. (Q) Do I need an Electronic Flasher if I just have LED tail lights? (A) It depends on the Bosch model flasher and the  manufacturing revision. Some of the Pantera flashers will operate with just LED tail lights. If there is both LED front signal lights and tail lights an LED type flasher is needed. There are some instances that the factory flasher may flash too fast to allow the LEDs to completely scroll across the tail light lens. In this case the Pantera Electronics adjustable rate signal flasher is required.  The information and items on this web-page are provided to assist in installing Pantera Electronics products in the Pantera electrical system. Pantera Electronics does not sell these items but all of the items can be purchased from Internet websites. PRODUCTS Ammeter Gauge Replacements Stewart Warner Deluxe Series P/N 82311 60-0-60 amps 2 1/16 in. diameter Black Gauge Face White Gauge Number White Pointer Color Stainless Steel Bezel VDO Cockpit P/N 190031 60-0-60 amps 2 1/16 in. diameter Black Gauge Face White Gauge Number Red Pointer Color Black Bezel VDO Vision P/N 190105 100-0-100 amps 2 1/16 in. diameter Black Gauge Face White Gauge Number Red Pointer Color Black Bezel ATO Fuse Holder Littelfuse P/N 01550400Z Male quick disconnect Wire size 18-22 AWG Molex P/N 19001-0003 Female quick disconnect wire size 18-22 AWG Molex P/N 19002-0001 Male quick disconnect Wire size 16-14 AWG Molex P/N 19001-0006 Female quick disconnect Wire size 16-14 AWG Molex P/N 19002-0024 Male quick disconnect wire size 10-12 AWG Molex P/N 19001-0010 Female quick disconnect Wire size 10-12 AWG Molex P/N 19002-0044 Terminal TAB Adapter, Molex P/N 19043-0020 Quick disconnect terminals colors and wire size, all compatible with the Pantera electrical system. Ring Tongue Terminal Stud Size 5/16 [M8] Wire Range 22-16 AWG Tyco P/N 34114 <-  Poor crimp quality,      lowest cost tool. <-  Very good crimp quality, ratcheting with interchangeable jaws. Paladin CrimpALL/8000 <-  Good crimp quality,      Ideal 30-429 Crimp Tools The only manufacturer of electronic technology designed exclusively for the de Tomaso Pantera Butt connector, Wire size 18-22 AWG Molex P/N 19154-0004 Butt connector, Wire size 14-16 AWG Molex P/N 19154-0015 Butt connector, Wire size 12-10 AWG Molex P/N 19164-0056